Mapei Kerapoxy CQ 3kg
- Suitable For: grouting ceramic tiles and mosaics.
- Area of use: INT & EXT
- Time to full cure: 24 hours
- Volume: 3kg
- Container Type: tub
- Type: grout
- Colour: 19 colours
- Brand: Mapei
- Manufactuer: Mapei
- Box Size: 1
Kerapoxy CQ is certified by the University of Modena (Italy) according to ISO 22196:2007 standards as a grouting mortar protected against the formation and proliferation of micro-organisms.
TECHNICAL CHARACTERISTICS
Kerapoxy CQ is a two-component, epoxy resin-based product with silica sand and other special components. It has excellent resistance to acids and is very easy to clean. Kerapoxy CQ has a bacteriostatic agent, preventing the proliferation of bacteria and forming mould on the surfaces of grouts, making tiled surfaces hygienic and safe, thanks to the innovative BioBlock technology developed as a result of MAPEI research. This is a product with very low emission of volatile organic compounds and is classified Emicode EC1 R Plus by GEV when used for grouting.
When applied correctly, it produces tile joints with the following characteristics:
• excellent mechanical strength and resistance to chemicals, therefore excellent durability;
• smooth and compact, surface finish which is non-absorbent and easy to clean; guarantees a high level of hygiene and blocks the formation of mildew and mould;
• high degree of hardness, excellent resistance to heavy traffic;
• no shrinkage and, therefore, no cracking;
• uniform colour, resistant to atmospheric agents;
• excellent workability, highly improved compared with traditional epoxy mortars thanks to its creamy consistency, which guarantees faster application times and makes it easier to clean the surfaces, with less waste and easier to obtain a good finish.
For more information about Mapei, please visit their website here.
For our range of mapei products, please click here. For more in the Kerapoxy range, please click here.
To calculate quantities, please use the Mapei grout calculator here
Please be advised that this is currently a non stock item & lead times may be slightly longer than expected, in comparison to our usual handling times.
Internal and external grouting of ceramic, stone material and glass mosaic floor finishes. Particularly suitable for grouting large areas where easy application and cleaning is required. Kerapoxy CQ allows you to create floors, walls and worktops, etc., in compliance with the HACCP system and the requirements of EC Regulation No. 852/2004 regarding hygiene and foodstuffs. Also suitable for acid-resistant bonding and rapid setting of ceramic tiles, stone materials, fibre-cement, concrete and any other building material on all types of substrates normally used in construction.
Some application examples
• Grouting materials with an uneven surface where it would be difficult to apply and clean traditional epoxy mortar.
• Grouting of floor tile finishes in the foodstuffs industry (dairies, cheese factories, abattoirs, breweries, wineries, preserves factories, etc.), shops and environments where a high level of hygiene is required (ice-cream parlours, butchers shops, fishmongers, etc.).
• Grouting of anti-bacterial tiles.
• Grouting of surfaces where a high protection against the formation and proliferation of micro-organisms is required.
• Grouting tiles on laboratory benches, kitchen worktops, etc.
• Grouting industrial floor tile finishes (galvanising plants, tanneries, battery rooms, paper works, etc.), where high mechanical strength and high resistance to attack by acids is required.
• Grouting swimming pools especially recommended for pools containing spa or seawater.
• Grouting floor tile finishes in steam rooms and Turkish baths.
• Acid-resistant bonding of tiles (used as an adhesive in compliance with class R2 specification according to EN 12004 standard).
• Bonding marble doorsteps and window-sills.
• Bonding tiles in plastic reinforced by fibreglass swimming pools.
• Bonding special pieces of tiles. Kerapoxy CQ may also be used to grout unglazed klinker, stone, polished porcelain or porcelain in contrasting colours. Always apply a small sample of the product in a trial area before using Kerapoxy CQ on wider surfaces.
APPLICATION
Preparation of the mix
Pour the catalyser (part B) into the container of part A and mix well until a smooth paste is obtained. We recommend using a low-speed electric mixer to guarantee perfect blending and to avoid overheating of the mix, which would reduce working times. Use the mix within 45 minutes of preparation.
Application
Spread Kerapoxy CQ over the tiled surface with a special MAPEI grout float, making sure that the joints are filled right down to the bottom. With the edge of the same float, strike off excess material.
Finish
After grouting with Kerapoxy CQ, floor finishes must be cleaned while the grout is still “fresh”. Cleaning of the joints may be carried out using a small amount of water and an abrasive sponge for cleaning joints (such as Scotch-Brite® or MAPEI tile-joints cleaning kit), followed by a cellulose sponge (MAPEI sponge, for example), taking care to avoid removing grout from the joints. The sponge must be saturated with water when cleaning finishes. The residual liquid may be removed with the same sponge, which must be replaced when it becomes too impregnated with resin, and the same technique may be used when finishing off the grouted joints. After the finishing operation, it is very important that no traces of Kerapoxy CQ remain on the surface. Once hardened, it is very difficult to remove. Therefore, rinse the sponge often with clean water during cleaning. In the case of very large floor surfaces, finishing may be carried out by wetting the surface and using a single-head rotary machine with special abrasive felt disks such as Scotch-Brite®. The residual liquid may be drawn off using a rubber squeegee. Kerapoxy Cleaner (special cleaning solution for epoxy grout) may also be used for the final cleaning cycle. It may also be used to remove thin residues of grout up to several hours after application. In this case, the product must be left to react for longer (at least 15-20 minutes). The efficiency of Kerapoxy Cleaner depends on the amount of residual resin and how much time has passed since application. Cleaning must always be carried out while the product is still “fresh”, as described above.
LIMITATIONS
• Even if it already seems clean after passing over the surface with a rubber float, always clean the surface using a Scotch-Brite pad and water to emulsify traces of resin on the surface, which could otherwise modify the final surface finish.
• Use Kerapoxy IEG to grout ceramic, and where floor finishes will be subject to attack by oleic acids (ham curers, sausage factories, oil mills, etc.) and aromatic hydrocarbons.
• Use a flexible sealant from the MAPEI range (such as Mapesil AC, Mapesil LM or Mapeflex PU45 FT) for flexible expansion joints or joints subject to movement.
• Kerapoxy CQ does not guarantee perfect bonding if the edges of the tiles are wet or contaminated with cement, dust, oil, grease, etc., during grouting.
• Do not use Kerapoxy CQ to grout terracotta tiles, the finish of the tiles may be altered.
• Always carry out preliminary tests before grouting stone or ground porcelain with a porous or rough surface.
• Do not add water or solvents to Kerapoxy CQ to increase its workability. • Use the product at temperatures between +12°C and +30°C. However, at temperatures below +15, °C application may be more difficult.
• The packages are pre-dosed, and, therefore, it is not possible to make mixing errors if all the contents are mixed. Do not rough guess the quantities when mixing the two components: hardening will be compromised if the catalysing ratio is wrong.
• If hardened and Kerapoxy CQ has to be removed from the joints, use an industrial hot air blower. If hardened localised residues of the product remain bonded to the tiles, use Pulicol 2000 for cleaning.
1 review for Mapei Kerapoxy CQ 3kg
You must be logged in to post a review.
| Elementlength | |||||||
| up to 1,5 m |
up to 2,5 m |
up to 3,5 m |
up to 4,5 m |
up to 2,5 m |
up to 3,5 m |
up to 4,5 m |
|
| Type of window frame material |
Minimum witdth of joints for a butled mounting b in mm |
Minimum witdth of joints for a inner mounting b in mm |
|||||
| Hard PVC (white) | 10 | 15 | 20 | 25 | 10 | 10 | 15 |
| Hard PVC and PMMA (dark) (colour extruded) |
15 | 20 | 25 | 30 | 10 | 15 | 20 |
| Hard PUR integral foam | 10 | 10 | 15 | 20 | 10 | 10 | 15 |
| Wood-aluminium-window | 10 | 10 | 15 | 20 | 10 | 10 | 15 |
| Aluminium-plastic sandwich frame (bright) |
10 | 10 | 15 | 20 | 10 | 10 | 15 |
| Aluminium-plastic sandwich frame (dark) |
10 | 15 | 20 | 25 | 10 | 10 | 15 |
| Wooden window frame | 10 | 10 | 10 | 10 | 10 | 10 | 10 |
Related Products
-
-
From: £4.28 inc. VAT
£3.57 ex. VAT -
-
-
From: £3.11 inc. VAT
£2.59 ex. VAT
From: £8.03 inc. VAT
£6.69 ex. VAT
From: £10.07 inc. VAT
£8.39 ex. VAT
From: £3.11 inc. VAT
£2.59 ex. VAT
From: £3.11 inc. VAT
£2.59 ex. VAT
From: £6.43 inc. VAT
£5.36 ex. VAT
From: £2.86 inc. VAT
£2.38 ex. VAT
From: £2.69 inc. VAT
£2.24 ex. VAT
From: £7.45 inc. VAT
£6.21 ex. VAT
From: £2.20 inc. VAT
£1.83 ex. VAT
From: £2.06 inc. VAT
£1.72 ex. VAT
-
£3.19 inc. VAT
£2.66 ex. VATBond-It De-Bond Mate is A non-drip gel formula for the complete removal of cured silicone sealant, particularly when silicone has been accidentally smeared over glass, ceramics or countertops. Removes all types of silicone sealant, leaving surfaces ready for re-sealing. For all other Bond-it products on our website, please click here. For any further information, you may need on Bond-it, please visit their website here. -
£2.94 inc. VAT
£2.45 ex. VATBond-it Flash Mate Lead Silicone is a low modulus neutral cure fast-skinning, roof sealant It is a high-performance neutral cure silicone sealant, specifically designed for use with roofing products both modern and traditional. For all other Bond-it products on our website, please click here. For an alternative silicone for lead, click here. For any further information you may need on Bond-it, please visit their website here. -
£9.06 inc. VAT
£7.55 ex. VATEverbuild 565 Clean Room Silicone is a neutral cure, low modulus, odourless sealant that adheres to a wide range of surfaces. Advantages - Mould Resistant for up to 10 years. - Bacterial resistance. - Excellent tooling and slow skinning properties. - Excellent adhesion properties to most surfaces. - Non-slump formula. - Excellent weathering properties. For application guns click here. For application tools click here. For all other Everbuild products on our website, please click here. For any further information on Everbuild products, please visit -
£6.78 inc. VAT
£5.65 ex. VATEverbuild Aqua Mate Sealant is a high modulus, reactive curing silicone sealant specially designed for aquariums. It remains permanently flexible & forms a watertight seal. Advantages - Everbuild Aqua Mate is free from fungicide and solvent - will not harm fish. - Fast cure - gives quick early strengths. - Extremely low dirt pick up. - Will withstand continuous water immersion. For application guns for this product, please click here. For all other Everbuild products on our site, please view here. For any further information on any Everbuild products, ple
JOHN DAY (verified owner) –
Took a week longer to arrive than I thought, but hey, the reason given was acceptable and understandable. Very good service and communication.