Bond It Rubber Bitumen Emulsion
- Suitable For: sandwich constructions and can also be used as a waterproofer for floors and walls
- Area of use: EXT
- Application Method: brush
- Container Type: tin
- Type: waterproofing emulsion
- Colour: dark brown
- Brand: Bond It
- Manufactuer: Bond It
Bond It Rubber Bitumen Emulsion is a solvent-free, rubberised bitumen emulsion which dries to a tough, black coating providing a highly effective cold-applied, damp-proof membrane in sandwich constructions. It can also be used as a waterproof for floors, walls and other above ground structures and acts as a curing membrane when applied to green concrete. It is equally effective as an adhesive for wood blocks, wood mosaic panels, insulation boards, expanded polystyrene and cork panels, or as a plaster bonding agent on difficult surfaces. It can also be applied to damp surfaces. Resistant to extreme heat and cold and has a low odour.
Storage Life
12 months from date of manufacture under good storage conditions in original, unopened containers. Store under cover out of direct sunlight, at a temperature of between 5oC and 40oC. Protect from frost – do not allow to freeze.
For all other Bond-it products on our website, please click here. For our full range of roofing products, click here.
For any further information you may need on Bond-it, please visit their website here.
Bond It Ruber Bitumen Emulsion provides a highly effective coldapplied, damp-proof membrane in sandwich constructions and can also be used as a waterproofer for floors, walls and other above ground structures. It also acts as a curing membrane when applied to green concrete.
It is equally effective as an adhesive for wood blocks, wood mosaic panels, insulation boards, expanded polystyrene and cork panels, or as a plaster bonding agent on difficult surfaces.
This product is also suitable for tanking silage pits.
APPLICATION
STIR WELL BEFORE USE.
– Damp‐proofing floors: Apply by brush, a minimum of 2 coats, each at 0.8 litres per m2 carrying the treatment up the walls to join the existing wall d.p.c. Allow the first coat to dry before applying the second coat at right-angles to the first. When dry, a sand/cement or concrete screed of approximately 50mm thick is then laid over the RUBBER BITUMEN EMULSION.
– Waterproofing walls: If a condition of rising damp exists, the best form of treatment must be the insertion of repair of a damp-proof course. Where dampness is due to penetration of the wall, proceed as follows:-
a) Exterior walls: level uneven surfaces, including brickwork, with cement mortar. Apply 3 coats of RUBBER BITUMEN EMULSION with a soft bristled brush, each at a rate of 0.5 litre per m2 allowing each coat to dry before applying the next. Allow the final coat to become tacky, then blind with clean, sharp sand.
b) Interior walls (moderately damp walls): remove wallpaper, loose emulsion or gloss paint and any dust or grease. Make good any damaged or perished plaster. Lightly dampen the prepared surface with clean water and apply 3 coats of RUBBER BITUMEN EMULSION with a soft bristled brush, each at the rate of 0.5 litre per m2 allowing each coat to dry before applying the next. A horizontal strip about 300mm deep should be left uncoated at the top running the whole length of the wall. This permits trapped moisture to escape by evaporation.
c) Interior walls (very damp walls): wherever possible very damp walls should receive an external treatment. If this is not possible the following procedure may be of benefit, although it must be emphasised that only adequate external treatments will cure the most severe conditions. The old plaster must be hacked away to expose the brickwork over the complete area, any damage to joints or brickwork should be made good with cement mortar to provide an even surface. When the mortar has set, apply 3 coats of RUBBER BITUMEN EMULSION each at the rate of 0.5 litre per m2 allowing complete drying between coats. When the final coat has thoroughly dried the wall should be replastered.
You must be logged in to post a review.
| Elementlength | |||||||
| up to 1,5 m |
up to 2,5 m |
up to 3,5 m |
up to 4,5 m |
up to 2,5 m |
up to 3,5 m |
up to 4,5 m |
|
| Type of window frame material |
Minimum witdth of joints for a butled mounting b in mm |
Minimum witdth of joints for a inner mounting b in mm |
|||||
| Hard PVC (white) | 10 | 15 | 20 | 25 | 10 | 10 | 15 |
| Hard PVC and PMMA (dark) (colour extruded) |
15 | 20 | 25 | 30 | 10 | 15 | 20 |
| Hard PUR integral foam | 10 | 10 | 15 | 20 | 10 | 10 | 15 |
| Wood-aluminium-window | 10 | 10 | 15 | 20 | 10 | 10 | 15 |
| Aluminium-plastic sandwich frame (bright) |
10 | 10 | 15 | 20 | 10 | 10 | 15 |
| Aluminium-plastic sandwich frame (dark) |
10 | 15 | 20 | 25 | 10 | 10 | 15 |
| Wooden window frame | 10 | 10 | 10 | 10 | 10 | 10 | 10 |
Related Products
From: £3.11 inc. VAT
£2.59 ex. VAT
From: £8.03 inc. VAT
£6.69 ex. VAT
From: £10.07 inc. VAT
£8.39 ex. VAT
From: £3.11 inc. VAT
£2.59 ex. VAT
From: £6.59 inc. VAT
£5.49 ex. VAT
From: £3.11 inc. VAT
£2.59 ex. VAT
From: £2.86 inc. VAT
£2.38 ex. VAT
From: £2.69 inc. VAT
£2.24 ex. VAT
-
£3.19 inc. VAT
£2.66 ex. VATBond-It De-Bond Mate is A non-drip gel formula for the complete removal of cured silicone sealant, particularly when silicone has been accidentally smeared over glass, ceramics or countertops. Removes all types of silicone sealant, leaving surfaces ready for re-sealing. For all other Bond-it products on our website, please click here. For any further information, you may need on Bond-it, please visit their website here. -
£2.94 inc. VAT
£2.45 ex. VATBond-it Flash Mate Lead Silicone is a low modulus neutral cure fast-skinning, roof sealant It is a high-performance neutral cure silicone sealant, specifically designed for use with roofing products both modern and traditional. For all other Bond-it products on our website, please click here. For an alternative silicone for lead, click here. For any further information you may need on Bond-it, please visit their website here. -
£9.06 inc. VAT
£7.55 ex. VATEverbuild 565 Clean Room Silicone is a neutral cure, low modulus, odourless sealant that adheres to a wide range of surfaces. Advantages - Mould Resistant for up to 10 years. - Bacterial resistance. - Excellent tooling and slow skinning properties. - Excellent adhesion properties to most surfaces. - Non-slump formula. - Excellent weathering properties. For application guns click here. For application tools click here. For all other Everbuild products on our website, please click here. For any further information on Everbuild products, please visit -
£6.78 inc. VAT
£5.65 ex. VATEverbuild Aqua Mate Sealant is a high modulus, reactive curing silicone sealant specially designed for aquariums. It remains permanently flexible & forms a watertight seal. Advantages - Everbuild Aqua Mate is free from fungicide and solvent - will not harm fish. - Fast cure - gives quick early strengths. - Extremely low dirt pick up. - Will withstand continuous water immersion. For application guns for this product, please click here. For all other Everbuild products on our site, please view here. For any further information on any Everbuild products, ple
Reviews
There are no reviews yet.