ARDEX MVS 95 Ready Mixed Moisture Vapour Suppressant 12kg
£182.44 inc. VAT
£152.03 ex. VAT
- Product ID: 22602
- Suitable For: suppressing residual construction moisture
- Area of use: INT
- Application Method: short pile roller
- Time to full cure: 2 hours
- Volume: 12KG
- Container Type: tub
- Type: waterproofer
- Colour: blue
- Brand: Ardex
- Manufactuer: Ardex
- Box Size: 1
ARDEX MVS 95 is a ready-to-use, one-component, water-based dispersion coating available in pre-gauged 12kg units. This pigmented blue coating indicates uniform coverage and becomes waterproof once fully cured. Designed to suppress residual construction moisture in cementitious substrates, including properly prepared power-floated concrete and cement/sand screeds, ARDEX MVS 95 is intended for use as a two-coat system. When fully dry, it creates a membrane that can accommodate hygrometer readings of up to 95% relative humidity (RH) and allows the subsequent application of ARDEX leveling and smoothing compounds without the need for priming. It is suitable for use on heated screeds installed and commissioned according to BS 8204 Part 1 and the recommendations in Part 4 of BS EN 1264, but it should not be applied directly to ground substrates without a functioning structural damp proof membrane. For applications lacking a structural damp proof membrane or where relative humidity exceeds 95% RH, consult the ARDEX DPM 1 C or ARDEX DPM 1 C R datasheet.
Key Points
- Product Overview: ARDEX MVS 95 is a water-based dispersion coating supplied in 12kg units, designed to suppress residual moisture in cementitious substrates.
- Waterproofing: The pigmented blue coating provides visual guidance for uniform coverage and becomes waterproof when fully cured.
- Moisture Tolerance: Two coats accommodate hygrometer readings up to 95% RH and allow for the direct application of leveling and smoothing compounds without priming.
- Usage Restrictions: Not suitable for direct application on ground substrates without a structural damp proof membrane; consult specific datasheets for alternatives.
Storage: Store ARDEX MVS 95 in a dry location, away from direct sunlight, and within a temperature range of 5°C to 30°C. Protect it from frost. The product has a shelf life of at least 12 months when kept in its original, unopened containers.
For more in our range of waterproofing, please click here. For more in our range from Ardex, click here.
Alternatively, you can visit the Ardex website here.
ARDEX MVS95 is specifically formulated to suppress residual construction moisture in cementitious substrates, including properly prepared power-floated concrete and cement/sand screeds. This product is intended for application as a two-coat system and effectively manages residual moisture in concrete slabs and cement/sand screeds. It is suitable for use on subfloors with relative humidity levels of up to 95% RH.
Substrate Preparation
Before applying ARDEX MVS95, ensure the surface is hard, dry, sound, and free of dust, laitance, dirt, and any other materials that could hinder adhesion, such as paint, lime coatings, plaster, or adhesive residues. Remove any standing water from the surface. Highly polished power-floated concrete, as well as curing agents, admixtures, and surface hardeners, may also affect adhesion. If there is any uncertainty regarding compatibility, perform a trial adhesion test with ARDEX MVS95 before proceeding. Any incompatible materials should be removed through grinding or shot blasting as needed.
Movement Joints
Do not bridge any joints or cracks in the floor that are subject to movement, such as structural movement joints, with ARDEX MVS95. Treat these joints with a flexible, impervious jointing system before application. Ensure structural movement joints are carried through to the final floor finish with an appropriate joint detail. For cracks in the screed or concrete that are not subject to movement but may compromise ARDEX MVS95, fully stitch and seal them with the appropriate ARDEX product, sand key while still wet, and allow to cure before applying ARDEX MVS95. Vacuum away any loose sand prior to application.
Application
Stir ARDEX MVS95 well before use. Do not add water or dilute the product, as it is ready to use. Avoid using ARDEX MVS95 when air temperatures are below 10°C and/or substrate temperatures are below 5°C. Apply an even coat using a suitable short-pile roller in one direction over the designated area. Depending on the applied film thickness, porosity of the subfloor, and ambient conditions, ARDEX MVS95 may dry in as little as 30 minutes at 20°C. Drying times may be longer in lower temperatures or high humidity. Once the first coat is touch dry, apply a second coat at right angles to the first. Ensure the applied ARDEX MVS95 forms a continuous film without pinholes, cavities, or thin patches; otherwise, additional applications may be required. Allow the surface to dry until it is tack-free, which will take approximately 1 hour at 20°C in good drying conditions. To protect the film, overlay ARDEX MVS95 with 3mm to a maximum of 10mm of an ARDEX Smoothing Compound, creating a uniform absorbent layer for subsequent floorcovering applications using the appropriate ARDEX Flooring Adhesive. Do not allow foot traffic between coats and ensure that no more than 24 hours elapse before applying the leveling and smoothing compound.
You must be logged in to post a review.
| Elementlength | |||||||
| up to 1,5 m |
up to 2,5 m |
up to 3,5 m |
up to 4,5 m |
up to 2,5 m |
up to 3,5 m |
up to 4,5 m |
|
| Type of window frame material |
Minimum witdth of joints for a butled mounting b in mm |
Minimum witdth of joints for a inner mounting b in mm |
|||||
| Hard PVC (white) | 10 | 15 | 20 | 25 | 10 | 10 | 15 |
| Hard PVC and PMMA (dark) (colour extruded) |
15 | 20 | 25 | 30 | 10 | 15 | 20 |
| Hard PUR integral foam | 10 | 10 | 15 | 20 | 10 | 10 | 15 |
| Wood-aluminium-window | 10 | 10 | 15 | 20 | 10 | 10 | 15 |
| Aluminium-plastic sandwich frame (bright) |
10 | 10 | 15 | 20 | 10 | 10 | 15 |
| Aluminium-plastic sandwich frame (dark) |
10 | 15 | 20 | 25 | 10 | 10 | 15 |
| Wooden window frame | 10 | 10 | 10 | 10 | 10 | 10 | 10 |
Related Products
-
£136.40 inc. VAT
£113.67 ex. VAT -
From: £109.79 inc. VAT
£91.49 ex. VAT
From: £109.79 inc. VAT
£91.49 ex. VAT -
-
£24.71 inc. VAT
£20.59 ex. VAT
£24.71 inc. VAT
£20.59 ex. VAT -
£241.68 inc. VAT
£201.40 ex. VAT
£241.68 inc. VAT
£201.40 ex. VAT
From: £3.56 inc. VAT
£2.97 ex. VAT
From: £8.03 inc. VAT
£6.69 ex. VAT
From: £11.34 inc. VAT
£9.45 ex. VAT
From: £3.60 inc. VAT
£3.00 ex. VAT
From: £6.59 inc. VAT
£5.49 ex. VAT
From: £4.21 inc. VAT
£3.51 ex. VAT
From: £4.36 inc. VAT
£3.63 ex. VAT
From: £3.48 inc. VAT
£2.90 ex. VAT
From: £14.11 inc. VAT
£11.76 ex. VAT
From: £47.33 inc. VAT
£39.44 ex. VAT
£34.20 inc. VAT
£28.50 ex. VAT
£34.20 inc. VAT
£28.50 ex. VAT
£28.24 inc. VAT
£23.53 ex. VAT
£28.24 inc. VAT
£23.53 ex. VAT
£53.38 inc. VAT
£44.48 ex. VAT
£138.05 inc. VAT
£115.04 ex. VAT
-
£3.24 inc. VAT
£2.70 ex. VATBond-It De-Bond Mate is A non-drip gel formula for the complete removal of cured silicone sealant, particularly when silicone has been accidentally smeared over glass, ceramics or countertops. Removes all types of silicone sealant, leaving surfaces ready for re-sealing. For all other Bond-it products on our website, please click here. For any further information, you may need on Bond-it, please visit their website here. -
£2.83 inc. VAT
£2.36 ex. VATBond-it Flash Mate Lead Silicone is a low modulus neutral cure fast-skinning, roof sealant It is a high-performance neutral cure silicone sealant, specifically designed for use with roofing products both modern and traditional. For all other Bond-it products on our website, please click here. For an alternative silicone for lead, click here. For any further information you may need on Bond-it, please visit their website here. -
£8.14£1.19 inc. VAT£6.78£0.99 ex. VAT
£8.14£1.19 inc. VAT£6.78£0.99 ex. VATARBO Arbosil 1070 represents a single-component, Low Modulus Silicone Sealant with Fire-Resistant properties. It undergoes curing upon exposure to moisture vapor, ultimately transforming into a highly flexible silicone rubber material. For more information on Arbo, please visit their website here. For more in our range of sealants, please click here. For application guns to use with this product, please click here. -
£3.61£1.19 inc. VAT£3.01£0.99 ex. VAT
£3.61£1.19 inc. VAT£3.01£0.99 ex. VATBond It LMH25 is a tough, flexible hybrid sealant ideal for installing internal and external window and door frames. Can also be used for sealing expansion and connection joints between most common substrates, without the use of a primer. PLEASE NOTE: THIS PRODUCT HAS A SHELF LIFE OF ONE MONTH BENEFITS - Solvent‐free & low odour. - Easy to tool and finish. - Can be overpainted with water based paints. - UV resistant. - Quick curing. - Contains no isocyanates, solvents, silicone and phthalates. - Excellent adhesion to most surfaces (even moist surf
Reviews
There are no reviews yet.